 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ABE0113 Low EMI Spread Spectrum Multiplier Clock FEATURES * * * * * * * Spread Spectrum Clock Generator with selectable multiplier ( 1x, 2x and 4x ). Output frequency ranges: 24MHz to 240MHz. Selectable Down Spread Modulation. TTL/CMOS compatible outputs. 3.3V Operating Voltage. Low short term jitter. Available in 8-Pin 150mil SOIC. PIN CONFIGURATION FIN S2^ S1^ S0v 1 8 VD D S3v FOUT GND ABE0113 2 3 4 7 6 5 FIN = 24 ~ 120 Mhz Note: v: 30k Internal Pull down ^: 30k Internal Pull up. DESCRIPTION The ABE0113 is a Spread Spectrum Clock Generator designed for the purpose of reducing EMI in highspeed digital systems. The selectable Down Spread modulation magnitude (see table below) permits EMI reduction without over-clocking the output. The device operates over a very wide range of input frequencies and provides 1x to 4x modulated clock outputs. OUTPUT CLOCK (FOUT) SELECTION S3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 S2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 S1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 S0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 FIN Range (MHz) 24 24 24 24 24 24 24 24 60 60 60 60 60 60 60 60 FOUT X1 X1 X1 X1 X2 X2 X2 X2 X2 X2 X4 X4 X1 X1 X1 X1 Spread Spectrum Modulation Frequency Magnitude -1.5% -2.0% -2.5% -3.0% -0.5% -1.0% -1.5% -2.0% -2.5% -3.0% -0.5% -1.0% -0.5% -1.0% -1.5% -2.0% 24 - 60 24 - 60 24 - 60 24 - 60 60 60 60 60 120 120 120 120 Fin / 1024 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/21/05 Page 1 ABE0113 Low EMI Spread Spectrum Multiplier Clock BLOCK DIAGRAM FIN PLL SST FOUT S(0:3) Control Logic PIN DESCRIPTIONS Name FIN S2 S1 S0 GND FOUT S3 VDD Number 1 2 3 4 5 6 7 8 Type I I I I P O I P Description Input Clock Frequency, 24MHz to 120MHz. Digital control input to select multiplication factor and SST modulation amplitude. Has internal pull-up. Digital control input to select multiplication factor and SST modulation amplitude. Has internal pull-up. Digital control input to select multiplication factor and SST modulation amplitude. Has internal pull-down. Ground. SST Modulated Clock Frequency Output. The frequency before modulation is synthesized by multiplying the input frequency by 1X, 2X, or 4X, depending on S(0:3). Digital control input to select multiplication factor and SST modulation amplitude. Has internal pull-down. 3.3V Power Supply. 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/21/05 Page 2 ABE0113 Low EMI Spread Spectrum Multiplier Clock ELECTRICAL SPECIFICATIONS 1. Absolute Maximum Ratings PARAMETERS Supply Voltage Input Voltage, dc Output Voltage, dc Storage Temperature Ambient Operating Temperature* Junction Temperature Lead Temperature (soldering, 10s) ESD Protection, Human Body Model SYMBOL VDD VI VO TS TA TJ MIN. -0.5 -0.5 -65 -40 MAX. 4.6 VDD+0.5 VDD+0.5 150 85 125 260 2 UNITS V V V C C C C kV Exposure of the device under conditions beyond the limits specified by Maximum Ratings for extended periods may cause permanent damage to the device and affect product reliability. These conditions represent a stress rating only, and functional operations of the device at these or any other conditions above the operational limits noted in this specification is not implied. * Note: Operating Temperature is guaranteed by design for all parts (COMMERCIAL and INDUSTRIAL), but tested for COMMERCIAL grade only. 2. DC/AC Specifications PARAMETERS Supply Voltage Input High Voltage Input Low Voltage Input High Current Input Low Current Output High Voltage Output Low Voltage Input Frequency Maximum interruption of FIN Input Capacitance Pull-up Resistor Pull-down Resistor Short Circuit Current 3.3V Dynamic Supply Current SYMBOL VDD VIH VIL IIH IIL VOH VOL FIN Cin1 Rpu Rpd Isc ICC CONDITIONS MIN. 2.97 0.7* VDD TYP. MAX. 3.63 0.3* VDD 100 100 UNITS V V V A A IOH=5mA, VDD =3.3V IOL=6mA, VDD =3.3V 2.4 24 4 30 30 50 20 0.4 120 none MHz s pF k k mA mA PIN 2, 3 PIN 4, 7 No Load 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/21/05 Page 3 ABE0113 Low EMI Spread Spectrum Multiplier Clock 3. TIMING CHARACTERISTICS PARAMETERS Rise Time Fall Time Output Duty Cycle Input to Output Delay Cycle to Cycle Jitter SYMBOL Tr Tf DT Tcyc-cyc CONDITIONS Measured at 0.8V ~ 2.0V @ 3.3V Measured at 2.0V ~ 0.8V @ 3.3V MIN. 0.8 0.78 45 2 TYP. 0.95 0.85 50 MAX. 1.1 0.9 55 4 100 UNITS ns ns % ns ps Over output frequency range @ 3.3V FUNCTIONAL DESCRIPTION Selectable spread spectrum and modulation rates The ABE0113 provides selectable multiplication factor, as well as selectable modulation rate. Selection is made by connecting pins 2 (S2), 3 (S1), 4 (S0), and 7 (S3) to a logical "zero" or "one", according to the output clock selection table on page 1. Default values for S(0:3) through internal pull-up and pull-down resistor Selection pins S0 and S3 have an internal pull-down resistor of 30k, pins 2 and 3 (S1 and S2) have an internal pull-up resistor of 30k. This internal pull-down (or pull-up) resistor will pull the input value to a logical "zero" (or "one" respectively) by default, i.e. when the pin is not connected to GND (VDD respectively). In order to override the internal pull-up (pull-down), the pin has to be connected to VDD (GND respectively). 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/21/05 Page 4 ABE0113 Low EMI Spread Spectrum Multiplier Clock PACKAGE INFORMATION 8 PIN Narrow SOIC ( mm ) SOIC Symbol A A1 B C D E H L e Min. 1.47 0.10 0.33 0.19 4.80 3.80 5.80 0.38 1.27 BSC Max. 1.73 0.25 0.51 0.25 4.95 4.00 6.20 1.27 A1 B e C L A D E H ORDERING INFORMATION For part ordering, please contact our Sales Department: 30332 Esperanza., Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 PART NUMBER The order number for this device is a combination of the following: Device number, Package type and Operating temperature range ABE0113 S C PART NUMBER TEMPERATURE C=COMMERCIAL I=INDUSTRIAL PACKAGE TYPE S=SOIC ABE0113SC-T ABE0113SC Order Number ABE0113SC ABE0113SC Marking SOIC -Tape and Reel SOIC -Tube Package Option Abracon Corporation, reserves the right to make changes in its products or specifications, or both at any time without notice. The information furnished by Abracon is believed to be accurate and reliable. However, Abracon makes no guarantee or warranty concerning the accuracy of said information and shall not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon this product. LIFE SUPPORT POLICY: Abracon's products are not authorized for use as critical components in life support devices or systems without the express written approval of the President of Abracon Corporation. 30332 Esperanza, Rancho Santa Margarita, Ca 92688 Ph: 949-546-8000 Fax: 949-546-8001 www.Abracon.com 03/21/05 Page 5 |
Price & Availability of ABE0113SC-T
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |